2007 Mazda MX-5

Nearside Front Anti-roll bar ball joint has slight play (5.3.4 (a) (i))

Offside Rear wheel slight bind

suspension components corroded

Emissions unable to be completed exhaust leak (8.2.1.2 (d))

Nearside Front Service brake excessively binding (1.2.1 (f))

Nearside Rear Shock absorbers has a serious fluid leak (5.3.2 (b))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill as marked (5.3.6 (a) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Offside Front Service brake binding but not excessively (1.2.1 (f))

Complete Under body corroded

Front Suspension arm pin or bush worn but not resulting in excessive movement Both (5.3.4 (a) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Underside corroded

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Front Suspension arm pin or bush worn but not resulting in excessive movement Both (5.3.4 (a) (i))

Nearside Rear Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Underside corroded

Exhaust has a minor leak of exhaust gases centre section (6.1.2 (a))

Rear Coil spring corroded corroded (5.3.1 (b) (i))

under body and suspension corroded

Front Coil spring fractured or broken both sides (5.3.1 (b) (i))

Exhaust has a minor leak of exhaust gases centre section (6.1.2 (a))

Rear Coil spring corroded corroded (5.3.1 (b) (i))

under body and suspension corroded

Brake hose has slight corrosion to ferrule All (1.1.12 (f) (i))

Front & rear suspension components, rust corrosion

Front Headlamp lens slightly defective Both (4.1.1 (b) (i))

Front Tracking is out

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement Back/rear (5.3.4 (a) (i))

Nearside Front Outer Tyre worn close to legal limit/worn on edge 205/50/16 (5.2.3 (e))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement Back/rear (5.3.4 (a) (i))

Offside Front Outer Tyre worn close to legal limit/worn on edge 205/50/16 (5.2.3 (e))

Rear Brakes are lightly binding on u/l

Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

both rear brakes binding slightly

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

both front tyres worn on outer edges

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Front Headlamp not working on dipped beam (1.7.5a)

Front Anti-roll bar linkage worn and seriously weakened (2.4.G.1)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Anti-roll bar linkage insecure (2.4.G.1)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)