1999 Yamaha Fazer

Headlamp light intensity reduced (4.1.4 (a))

Drive chain slightly loose (6.1.7 (c) (i))

Nearside Front Shock absorber has a light misting of oil (5.3.2 (b))

Offside Front Shock absorber has a light misting of oil (5.3.2 (b))

Rear Rear wheel has a non standard spindle arrangement, however rear wheel is secure when presented

Nearside Front Shock absorber has a light misting of oil (5.3.2 (b))

Front Brake binding but not excessively (1.2.1 (f))

Offside Front Shock absorber has a light misting of oil (5.3.2 (b))

Front tyre starting to age crack between treads

Gear change pivot worn

Slight exhaust blow

Slight fluctuation,rear brake

Nearside Rear Direction indicator not working (1.5.1c)

Offside Front shock absorber seal failed and leaking oil (2.3.3)

Gear change pivot worn

Nearside Front shock absorber has light misting of stanchion (2.3.3)

Rear Roller brake test indicates a slightly juddering brake (3.3.A1b)

Slight exhaust blow at silencer joint

Front Front position lamp does not illuminate immediately when switched on (1.1.3a)

Front Roller brake test indicates a binding brake (3.3.A1a)

Headlamp aim too high (1.6)

Exhaust is leaking but is not excessively noisey (7.1.1b)

Front Tyre worn close to the legal limit (4.1.3(ii))

Slight bind,rear brake

Nearside Front Footrest insecure (6.2.1a)

Rear Roller brake test indicates excessive fluctuation of brake effort (3.3.A1d)

Exhaust is leaking but is not excessively noisey (7.1.1b)

Front Tyre worn close to the legal limit (4.1.3(ii))

front brake slightly binding

Brake lever has inadequate reserve travel (3.1.3b)

Front Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Front Floor brake test indicates a binding brake (3.3.C2c)

Rear Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Drive chain slightly loose (6.2.1d)

Exhaust is leaking but is not excessively noisey (7.1.1b)

Exhaust slightly deteriorated (7.1.1a)

Front Roller brake test indicates a slightly grabbing brake (3.3.A1b)

Headlamp masks/converters fitted

Only 50% of rear position lamp working

Upon removal of rear brake caliper for rear tyre replacement found that for both brake pads the friction material has started to lift from the backing plate.

Front Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))

Rear Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort (3.3.A1c)

Rear Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))

Registration plate with character(s) which are not the correct width (6.3.4a)

Drive chain slightly loose (6.2.1d)

Exhaust is leaking but is not excessively noisey (7.1.1b)

Exhaust slightly deteriorated (7.1.1a)

Front Roller brake test indicates a slightly grabbing brake (3.3.A1b)

Only 50% of rear position lamp working

Unable to inspect rear brake fluid reservoir without removing side panel which is not permitted during Mot inspection

Drive chain excessively loose (6.2.1d)

Headlamp aim beam image kick up to the offside (1.6)

Front Tyre worn close to the legal limit (4.1.3(ii))

Nearside Front Brake disc(s) slightly worn (3.2.A1l)

Offside Front Brake disc(s) slightly worn (3.2.A1l)

Headlamp aim beam image kick up to the offside (1.6)

Registration plate characters incorrectly spaced (6.3.4a)

Registration plate with character(s) which are not the correct height (6.3.4a)

Registration plate with character(s) which are not the correct stroke width (6.3.4a)

Registration plate with character(s) which are not the correct width (6.3.4a)

Front Tyre worn close to the legal limit (4.1.3(ii))

Nearside Front Brake disc(s) slightly worn (3.2.A1l)

Offside Front Brake disc(s) slightly worn (3.2.A1l)

Exhaust is leaking but is not excessively noisey (7.1.1b)