2010 Mazda Bongo

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Exhaust has a major leak of exhaust gases exhaust flexi pipe (6.1.2 (a))

Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Nearside Rear Anti-roll bar pin or bush excessively worn 'D' bush (5.3.4 (a) (i))

Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i))

Nearside Rear Position lamp not working (4.2.1 (a) (ii))

Offside Rear Anti-roll bar pin or bush excessively worn 'D' bush (5.3.4 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Offside Front Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Rear Service brake binding but not excessively (1.2.1 (f))

Rear Exhaust mounting defective (6.1.2 (a))

lower radiator panel corroded/holed

Front Integral body structure is corroded but structural rigidity is not significantly reduced crossmember/radiator panel (6.1.1 (c) (i))

Front Service brake binding but not excessively both (1.2.1 (f))

Front radiator panel/crossmember corroded

Offside headlamp lens faded

Emissions not tested (8.2.1.2 (d))

Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Front Service brake binding but not excessively both (1.2.1 (f))

Front radiator panel/crossmember corroded

Offside headlamp lens faded

Front Integral body structure is corroded but structural rigidity is not significantly reduced crossmember/rad panel (6.1.1 (c) (i))

Front Integral body structure is corroded but structural rigidity is not significantly reduced crossmember rad panel (6.1.1 (c) (i))

Offside headlamp lens faded

Emissions not tested due to exhaust leak (8.2.1.2 (d))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing panel holed+corroded (under battery tray) (6.2.2 (d) (i))

Offside Headlamp lens seriously defective (4.1.1 (b) (ii))

Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill holed+corroded front and rear (6.1.1 (c) (i))

Rear Exhaust has a major leak of exhaust gases silencer+pipe holed (6.1.2 (a))

Front crossmemeber/rad panel corroded

Front crossmember/rad panel corroded

Offside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sill corroded (6.1.1 (c) (i))

Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Rear Anti-roll bar pin or bush excessively worn x2 saddle bushes worn (5.3.4 (a) (i))

Front crossmember/rad panel corroded

Offside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sill corroded (6.1.1 (c) (i))

Emissions not tested (8.2.1.2 (d))

Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b))

Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i))

Rear Exhaust has a major leak of exhaust gases mid/rear flex joint (6.1.2 (a))

Front crossmember slightly corroded

Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER SILL (6.1.B.2)

Nearside Front position lamp(s) incorrect colour (1.1.A.3e)

Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER SILL (6.1.B.2)

Offside Front position lamp(s) incorrect colour (1.1.A.3e)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL (6.1.B.2)

Parking brake lever has no reserve travel (3.1.6b)

Rear fog lamp emits a light other than red (1.3.2e)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill (2.4.A.3)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Nearside Front Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)

Nearside Seat belt anchorage prescribed area is excessively corroded outer sill (5.2.6)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)

Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill (2.4.A.3)

Offside Seat belt anchorage prescribed area is excessively corroded outer sill (5.2.6)

Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside front brake binding (3.7.B.1)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside front brake binding (3.7.B.1)

Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

2 x baby seats fitted at rear

front and rear pads low

Nearside Headlamp aim too low (1.8)

Offside Headlamp aim too low (1.8)

Rear fog lamp not working (1.3.2b)

2 x baby seats fitted at rear

front and rear pads low