1995 Mazda Bongo

Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Shock absorbers has a serious fluid leak (5.3.2 (b))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))

Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outrigger (7.1.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i))

Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i))

Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i))

Offside Front Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge 3mm (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge 3mm (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill to outrigger (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill to outrigger (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i))

Nearside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Front Tyre worn close to legal limit/worn on edge 3mm (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge 3mm (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

Spare tyre defective deflated ()

Front Suspension component mounting prescribed area is corroded but not considered excessive inner sills corroded outside prescribed areas (5.3.6 (a) (i))

Nearside Rear Nail in tyre ()

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))

Offside Rear Suspension component mounting repair covered in underseal filler in outer sill and sill end panel covered in mastic (5.3.6 (a) (i))

Fuel system component leaking injection pump area (6.1.3 (b) (i))

Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Offside Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii))

Front Suspension component mounting prescribed area is corroded but not considered excessive inner sills corroded outside prescribed areas (5.3.6 (a) (i))

Nearside Rear Nail in tyre ()

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))

Offside Rear Suspension component mounting repair covered in underseal filler in outer sill and sill end panel covered in mastic (5.3.6 (a) (i))

Spare tyre defective deflated ()

Front Suspension component mounting prescribed area damaged but not considered excessive inner sills corroded outside prescribed area's (5.3.6 (a) (i))

Nearside Rear Suspension component mounting repair covered in underseal filler in outer sill (5.3.6 (a) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing splitting between treads (5.2.3 (d) (ii))

Offside Rear Suspension component mounting repair covered in underseal sill end panel (5.3.6 (a) (i))

Rear Oil leak, but not excessive (8.4.1 (a) (i))

Spare tyre defective ()

Fuel system component leaking fuel injection pump (6.1.3 (b) (i))

Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i))

Offside Headlamp not working on main beam (4.1.1 (a) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i))

Front Suspension component mounting prescribed area damaged but not considered excessive inner sills corroded outside prescribed area's (5.3.6 (a) (i))

Nearside Rear Suspension component mounting repair covered in underseal filler in outer sill (5.3.6 (a) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing splitting between treads (5.2.3 (d) (ii))

Offside Rear Suspension component mounting repair covered in underseal sill end panel (5.3.6 (a) (i))

Rear Oil leak, but not excessive (8.4.1 (a) (i))

Spare tyre defective ()

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Rear Tyre slightly damaged/cracking or perishing cracking between treads (5.2.3 (d) (ii))

Offside Rear Suspension component mounting repair covered in underseal filler in outer sill panel (5.3.6 (a) (i))

Offside Rear Suspension component mounting repair covered in underseal sill end panel covered in mastic (5.3.6 (a) (i))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Oil leak, but not excessive gearbox oil cooler pipe (8.4.1 (a) (i))

Spare tyre defective deflated ()

Fuel system component leaking fuel pump area (6.1.3 (b) (i))

Horn not working (7.7 (a) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Nearside Front Suspension arm modified so the suspension is likely to foul other components anti roll bar link too long (5.3.3 (c) (ii)) DANGEROUS

Nearside Front Tyre has a tear, caused by separation or partial failure of its structure spitting between treads (5.2.3 (d) (ii)) DANGEROUS

Offside Front Tyre has a tear, caused by separation or partial failure of its structure splitting between treads (5.2.3 (d) (ii)) DANGEROUS

Offside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Nearside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Rear Tyre slightly damaged/cracking or perishing cracking between treads (5.2.3 (d) (ii))

Offside Rear Suspension component mounting repair covered in underseal filler in outer sill panel (5.3.6 (a) (i))

Offside Rear Suspension component mounting repair covered in underseal sill end panel covered in mastic (5.3.6 (a) (i))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Oil leak, but not excessive gearbox oil cooler pipe (8.4.1 (a) (i))

Spare tyre defective deflated ()

Nearside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Oil leak, but not excessive gearbox oil cooler pipe connection (8.4.1 (a) (i))

Oil leak, but not excessive upper engine (8.4.1 (a) (i))

Spare tyre defective deflated ()

Fuel system component leaking fuel pump (6.1.3 (b) (i))

Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i))

Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i))

Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced rear most wheel arch and wheel arch liner (7.1.1 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Nearside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Windscreen wiper blade defective (3.4 (b) (i))

Oil leak, but not excessive gearbox (8.4.1 (a) (i))

Rear fog lamp insecure (4.5.1 (c) (i))

Spare tyre defective deflated ()

Upper Oil leak, but not excessive engine (8.4.1 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive crossmember (5.3.6 (a) (i))

fuel pump area damp

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Rear fog lamp missing (4.5.1 (a) (ii))

Nearside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Front Tyre has ply or cords exposed inner edge (5.2.3 (d) (ii)) DANGEROUS

Nearside Front Tyre worn close to legal limit/worn on edge inner edge (5.2.3 (e))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive crossmember (5.3.6 (a) (i))

fuel pump area damp

Nearside Front Front constant velocity joint gaiter damaged, but preventing the ingress of dirt outer (2.5.C.1a)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive outer sill (2.4.A.3)

Nearside Rear Seat belt anchorage prescribed area is excessively corroded wing and inner wheel arch panel (5.2.6)

Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill (2.4.A.3)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Rear Seat belt affected by an insecure seat fixing (5.2.1b)

Offside Registration plate lamp not working (1.1.C.1d)

Nearside Front Front constant velocity joint gaiter damaged, but preventing the ingress of dirt outer (2.5.C.1a)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive outer sill (2.4.A.3)

spare tyre flat

Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement D bush (2.4.G.2)

Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c)

Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement D bush (2.4.G.2)

Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Rear fog lamp missing (1.3.2a)

spare tyre flat

Nearside Rear Outer sill corroded

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Rear Outer sill corroded

front cross member rusty

Under-trays fitted obscuring some underside components

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Front Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Rear Anti-roll bar has excessive play in a pin/bush (2.4.G.2)

Offside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Rear fog lamp not working (1.3.2b)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1) DANGEROUS

Oil leak

Under-trays fitted obscuring some underside components

Front Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

under body surface rust

Centre Exhaust has a major leak of exhaust gases (7.1.2)

Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c)

Offside Registration plate lamp not working (1.1.C.1d)

Front Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

under body surface rust

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

front break hoses slightly perrished

oil leak

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Registration plate lamp not working (1.1.C.1d)

Rear fog lamp not working (1.3.2b)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

front break hoses slightly perrished

oil leak

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front constant velocity joint gaiter split (2.5.C.1a)

Offside Front constant velocity joint gaiter split (2.5.C.1a)

Offside Registration plate lamp not working (1.1.5c)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Rear Exhaust has part of the system excessively deteriorated (7.1.1a)

Rear fog lamp switch missing (1.3.1a)

Offside Front Tyre worn close to the legal limit (4.1.E.1)