2013 Mini John Cooper Works

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b))

Exhaust carbon monoxide content at idle exceeds manufacturer's specified limits (8.2.1.2 (b))

Exhaust catalytic converter missing where one was fitted as standard (8.2.2.1 (a))

Front Service brake fluctuating, but not excessively (1.2.1 (e))

Offside Obligatory mirror slightly damaged (3.3 (b) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Front Suspension arm pin or bush worn but not resulting in excessive movement both (5.3.4 (a) (i))

Offside Front Inner Wheel arch trim missing

Some coolant/boost pipes cable tied to other components

Suspension unit modified but function not affected Coil over suspension fitted (5.3.5 (b) (i))

Windscreen damaged but not adversely affecting driver's view chip (3.2 (a) (i))

Driver's view of the road through the swept area of the windscreen significantly affected by an obstruction sunstrip (3.1 (a) (ii))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a))

Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Nearside Front Inner Tyre fouling a part of the vehicle wheel arch trim (5.2.3 (f))

Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Headlamp insecure (4.1.1 (c))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Sub-frame attachment bracket/mounting insecure snapped bolt (5.3.3 (a) (i))

Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Rear Direction indicator lens defective such that the emitted light is adversely affected tinted (4.4.1 (b) (ii))

Rear Stop lamp(s) lens defective such that the emitted light is adversely affected tinted (4.3.1 (b) (ii))

Steering system excessively rough steering rack clicking and grinding inside the rack. (2.1.1 (a))

Windscreen washer not working (3.5 (a))

Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Nearside Rear Lower Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Front Inner wheel arch trim missing

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Offside Rear Lower Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Rear All position lamps have a product on the lenses but not adversely affecting light output tinted (4.2.3 (b) (ii))

Suspension unit modified but function not affected coilover kit fitted (5.3.5 (b) (i))

Windscreen damaged but not adversely affecting driver's view chip (3.2 (a) (i))

some coolant pipes and some boost pipes under vehicle at the front have been cable tied onto other components

vehicle too low for RBT so tapley used

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Nearside Side repeater not working (4.4.1 (a) (ii))

Offside Side repeater not working (4.4.1 (a) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Front Anti-roll bar has slight play in a ball joint both (2.4.G.2)