MOT Status
ExpiredMileage
198,781 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Front Sub-frame corroded and seriously weakened (5.3.3 (b) (i))
Horn not working (7.7 (a))
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))
Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))
Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill (5.3.6 (a) (ii)) DANGEROUS
Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wheel arch (5.3.6 (a) (ii)) DANGEROUS
Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill (5.3.6 (a) (ii)) DANGEROUS
Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wheel arch (5.3.6 (a) (ii)) DANGEROUS
Nearside Front drive shaft missing
Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Rear Lower Anti-roll bar linkage pin or bush worn but not resulting in excessive movement bush (5.3.4 (a) (i))
Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Oil leak, but not excessive engine (8.4.1 (a) (i))
Windscreen wiper blade defective rubber split on end of blade (3.4 (b) (i))
Offside Front Brake pipe excessively corroded (1.1.11 (c))
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch around brake pipe (5.3.6 (a) (i))
Rear fog lamp not working (4.5.1 (a) (ii))
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS
Nearside Front drive shaft missing
Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Rear Lower Anti-roll bar linkage pin or bush worn but not resulting in excessive movement bush (5.3.4 (a) (i))
Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Oil leak, but not excessive engine (8.4.1 (a) (i))
Windscreen wiper blade defective rubber split on end of blade (3.4 (b) (i))
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i))
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis\wheel arch (5.3.6 (a) (i))
Offside Front Brake pipe excessively corroded (1.1.11 (c))
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis\inner wing (5.3.6 (a) (i))
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i))
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/wheel arch (5.3.6 (a) (i))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Rear fog lamp not working (4.5.1 (a) (ii))
Nearside Front driveshaft missing
Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Rear Lower Anti-roll bar pin or bush worn but not resulting in excessive movement bush (5.3.4 (a) (i))
Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Oil leak, but not excessive engine (8.4.1 (a) (i))
Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))
Nearside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Nearside Front driveshaft removed
Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))
underside of vehicle has had major welding and has been heavily undersealed
Nearside Front Lower Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))
Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Nearside Rear Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Offside Front Sub-frame is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i))
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))
Service brake efficiency below requirements (1.2.2 (a) (i))
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS
Central Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Nearside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Nearside Front NSF DRIVESHAFT MISSING
Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Nearside Rear Outer Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Outer Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Offside Rear Outer Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Inner INNER SILLS NOT REPAIRED CORRECTLY
Offside Inner INNER SILLS NOT REPAIRED CORRECTLY
brake pipes heavily coated in a protective wax (front to rear)
under body + components heavily coated in a protective wax (front to rear)
Exhaust system not adequately supported (7.1.1)
Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill (6.1.B.2)
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg (6.1.B.2)
Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill (6.1.B.2)
Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill (6.1.B.2)
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush drop link (2.4.G.2)
Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)
Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings box section (6.1.B.2)
Parking brake: efficiency below requirements (3.7.B.7)
Rear cross member corroded
brake pipes heavily coated in a protective wax (front to rear)
under body + components heavily coated in a protective wax (front to rear)
rear seat missing
underside corroded
Front Sub-frame corroded and seriously weakened (2.4.G.1)
Nearside Front Anti-roll bar linkage insecure (2.4.G.1)
Nearside Front Subframe mounting prescribed area is excessively corroded At front mount (2.4.A.3)
Nearside Front Subframe mounting prescribed area is excessively corroded At rear mount (2.4.A.3)
Nearside Front Subframe mounting prescribed area is inadequately repaired (2.4.A.3)
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill (2.4.A.3)
Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)
Offside Front Subframe mounting prescribed area is excessively corroded At rear mount (2.4.A.3)
Offside Front Suspension arm has excessive play in a pin/bush rear bush (2.4.G.2)
Offside Rear Passenger's seat insecure (6.2.A.1)
Offside Rear Seat belt anchorage prescribed area is excessively corroded inner arch (5.2.6)
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c)
Parking brake: efficiency below requirements (3.7.B.7)
Rear fog lamp emits a light other than red (1.3.2e)
Subframe mounting prescribed area is inadequately repaired Front crossmember (2.4.A.3)
Vehicle structure has excessive damage seriously affecting its strength within 30cm of a towbar mounting (6.6.6)
Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Suspension arm has slight play in a pin/bush osf (2.4.G.2)
Vehicle structure has slight corrosion both rear quarter inners (6.1.B.2)
Vehicle structure has slight corrosion rear cross member (6.1.B.2)
oil leak
Nearside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)
Nearside Front Headlamp not working on dipped beam (1.7.5a)
Nearside Front Tie bar/rod has excessive play in a ball joint (2.4.G.2)
Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Front front brake application uneven (3.7.B.2) DANGEROUS
Nearside Rear front parking brake recording little or no effort (3.7.B.6a) DANGEROUS
Parking brake: efficiency below requirements (3.7.B.7) DANGEROUS
Exhaust has a minor leak of exhaust gases (7.1.2)
Suspension arm has slight play in a track control arm inner bush (2.5.B.2b)
Brake pad(s) wearing thin (3.5.1g)
Nearside Front Suspension arm has slight play in a pin/bush (2.4.G.2)
Brake pad(s) wearing thin (3.5.1g)
Nearside Front Headlamp not working on dipped beam (1.7.5a)
Nearside Front Suspension arm has slight play in a pin/bush (2.4.G.2)
Nearside Rear Registration plate lamp not working (1.1.5c)
Offside Rear Rear fog lamp missing (1.3.2a)
Nearside Front Headlamp not in good working order adversely affecting beam image (1.2.4a)
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)
Nearside rear parking brake recording little or no effort (3.7.B.6a)
Offside Front Headlamp aim too high (1.8)
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)
Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)
Offside Rear fog lamp missing (1.3.2a)
Oil leak
Offside Rear fog lamp missing (1.3.2a)
Offside Front Front constant velocity joint gaiter split (2.5.C.1a)
Offside Rear Rear fog lamp not working (1.3.2b)
Offside Rear Anti-roll bar attachment bracket/mounting cracked (2.4.G.1)
Parking brake lever has no reserve travel (3.1.6b)
How Reliable is the Mazda Bongo?
Based on 251,584 MOT tests across 14,362 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
M860 VPT is a 2005 Mazda Bongo in Green with a 2,500cc diesel engine. This vehicle has been through 26 MOT tests with a personal pass rate of 53.8%.
Across all 2005 Mazda Bongo models, the average MOT pass rate is 66.8% with a typical mileage of 133,806 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Mazda Bongo fails its MOT is fog lamp not working, accounting for 6,854 recorded failures. If you're considering buying M860 VPT, it's worth having these areas checked by a mechanic before committing.
The Mazda Bongo typically stays on UK roads for around 31 years. At 21 years old, this Mazda Bongo is well into its expected lifespan but still has years ahead.
Frequently Asked Questions
How do I check the history of M860 VPT?
You can check the full history of M860 VPT by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was M860 VPT registered?
M860 VPT is a 2005 Mazda Bongo, first registered on 9 March 2005.
Is M860 VPT safe to buy?
The MOT history for M860 VPT shows 26 tests with a 53.8% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does M860 VPT have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on M860 VPT. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.