1993 Honda Integra

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill x2 (5.3.6 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Front Brake hose has slight corrosion to ferrule both sides (1.1.12 (f) (i))

Front Brake pipe corroded, covered in grease or other material both sides (1.1.11 (c))

Front Coil spring corroded both sides (5.3.1 (b) (i))

Front Subframe mounting prescribed area is corroded but not considered excessive both sides (5.3.6 (a) (i))

Headlamp has a product on the lens but not seriously reducing light output both sides (4.1.4 (b))

Integral body structure is corroded but structural rigidity is not significantly reduced floor areas front to rear (6.1.1 (c) (i))

Nearside Front Outer Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Service brake binding but not excessively (1.2.1 (f))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner arm mounting area (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner arm mounting area (5.3.6 (a) (i))

Rear Brake hose has slight corrosion to ferrule both sides (1.1.12 (f) (i))

Rear Brake pipe corroded, covered in grease or other material both sides (1.1.11 (c))

Rear Coil spring corroded both sides (5.3.1 (b) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Headlamp lens slightly defective both (4.1.1 (b) (i))

Suspension component corroded but not seriously weakened +sills+floor+fuel lines+chassis members (5.3.3 (b) (i))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Headlamp not working on main beam (4.1.1 (a) (ii))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Headlamp lens slightly defective both (4.1.1 (b) (i))

Suspension component corroded but not seriously weakened +sills+floor+fuel lines+chassis members (5.3.3 (b) (i))

Brake hose has slight corrosion to ferrule all (1.1.12 (f) (i))

Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Central Stop lamp(s) non-obligatory stop lamp not working (4.3.1 (a) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Windscreen wiper blade defective both (3.4 (b) (i))

all front suspension components corroded

all fuel lines very corroded

all rear suspension components corroded

under side very corroded

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b))

Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))

Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))

Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Front Brake pipe at imminent risk of failure or fracture too rear both sides (1.1.11 (a)) DANGEROUS

Brake hose has slight corrosion to ferrule all (1.1.12 (f) (i))

Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Central Stop lamp(s) non-obligatory stop lamp not working (4.3.1 (a) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material too hose (1.1.11 (c))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Front Brake pipe corroded, covered in grease or other material too hose (1.1.11 (c))

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Windscreen wiper blade defective both (3.4 (b) (i))

all front suspension components corroded

all rear suspension components corroded

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt both (2.1.3 (g) (i))

Offside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Suspension component corroded but not seriously weakened +floor+coil springs+front crossmember (5.3.3 (b) (i))

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section (5.3.6 (a) (i))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt both (2.1.3 (g) (i))

Offside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Suspension component corroded but not seriously weakened +floor+coil springs+front crossmember (5.3.3 (b) (i))

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Coil spring corroded all four (5.3.1 (b) (i))

Front Lower Power steering pipe/hose slightly corroded (2.1.5 (g) (i))

Front to rear fuel pipes and brake pipes slightly corroded

General corrosion underside vehicle in places

Nearside Rear Upper Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

No engine oil reading on dipstick prior to test

Offside front outer constant velocity joint gaiter seeping grease

Offside rear ABS wiring loom insecure

Plastic side skirts fitted not allowing full inspection of sills

Rear Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Shock absorbers has slight external damage to the casing all four casings corroded (5.3.2 (b))

All four coil springs are corroded

All four shock absorbers are corroded

Front Lower Power steering pipe/hose slightly corroded (2.1.5 (g) (i))

Front to rear fuel pipes and brake pipes slightly corroded

General corrosion to underside vehicle in places

Oil leak, but not excessive (8.4.1 (a) (i))

Plastic side skirts fitted not allowing full inspection of sills

Rear Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Drive shaft joint excessively worn (6.1.7 (c) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

All four coil springs are corroded

All four shock absorbers are corroded

Auxiliary drive belts are perished/cracked

Both front headlamp plastic lenses are tarnished, close to masking beam patterns

Front Lower Power steering pipe/hose slightly corroded (2.1.5 (g) (i))

Front to rear fuel pipes and brake pipes slightly corroded

General corrosion to underside vehicle in places

Nearside Front Steering rack gaiter damaged or deteriorated, but preventing the ingress of dirt split (2.1.3 (g) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Plastic side skirts fitted not allowing full inspection of sills

Rear Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt nearside front and offside front (2.1.3 (g) (i))

rear tyres wearing on edges+getting low on tread,rear panels corroded,front tyres wearing on edges

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill+along inside (5.3.6 (a) (i))

Nearside Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Offside Registration plate lamp missing in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Windscreen damaged and affecting the driver's view of the road (3.2 (a) (ii))

rear tyres wearing on edges+getting low on tread,rear panels corroded,front tyres wearing on edges

suspension components+brake pipes+ferrules+brake back plates+floor pans+rear panels corroding,offside rear abs wire insecure,h/lamps poor condition

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength end cover sill (5.3.6 (a) (i))

Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i))

Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

offside rear abs wire insecure,offside rear sill end cover corroded,h/lamps poor condition

suspension components+floor pans+rear panels+brake back plates corroded,brake pipes+ferrules corroding,sill covers fitted

sills n/s+o/s at front corroding,sill covers fitted

suspension components corroding,offside rear abs bracket broken off

Emissions not tested (7.3.A.1)

Front Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded sill to floor (2.4.A.3)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill to floor+chassis member (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded innersill (2.4.A.3)

Offside Registration plate lamp not working (1.1.C.1d)

suspension components corroding,offside rear abs bracket broken off

both rear tyres wearing on edges,oil leaks

suspension components+chassis members+floor+sills+brake back plates corroding

Offside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Headlamp aim too low (1.8)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Trailing arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Nearside Rear Upper Suspension arm has excessive play in a pin/bush (2.4.G.2)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Trailing arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Rear Upper Suspension arm has excessive play in a pin/bush (2.4.G.2)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Front Front constant velocity joint gaiter damaged, but preventing the ingress of dirt (2.5.C.1a)

Nearside Front Upper Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Track rod end ball joint dust cover damaged, but preventing the ingress of dirt (2.2.C.1c)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Trailing arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Trailing arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

nearside rear inner sill heavily undersealed

unable to full check the condition of the outer sills due to side skirts fitted

unable to fully check to condition of the rear inner wheel arches due to being bodyfilled

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Nearside Headlamp aim too low and too far to the right. (1.8)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Steering rack gaiter split (2.2.D.2d)

Offside Front Wheel nut(s) missing (4.2.A.1e)

Offside Headlamp aim too high and too far to the left. (1.8)

Offside Rear fog lamp not working (1.3.2b)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Trailing arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Trailing arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

unable to full check the condition of the outer sills due to side skirts fitted

unable to fully check to condition of the rear inner wheel arches due to being bodyfilled

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Steering rack gaiter split (2.2.D.2d)

Front Exhaust has a major leak of exhaust gases (7.1.2)

Front brake disc in such a condition that it is seriously weakened (3.5.1i)

Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Parking brake lever has no reserve travel (3.1.6b)

Parking brake: efficiency below requirements (3.7.B.7)

Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Rear brake disc in such a condition that it is seriously weakened (3.5.1i)

Tyre worn close to the legal limit (4.1.E.1)

Offside Rear brake disc excessively pitted (3.5.1h)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Front registration plate deteriorated (6.3.1d)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Headlamp aim too low (1.8)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Rear registration plate has a feature which changes the appearance or legibility of the characters (6.3.4c)

Rear Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Nearside Headlamp aim too low (1.8)

Parking brake: efficiency below requirements (3.7.B.7) DANGEROUS

Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

brake fluid level on minimum

corrosion to rear cross member ;rear chassis legs

front number plate damaged

Nearside Front constant velocity joint gaiter split (2.5.C.1a)

Offside Front constant velocity joint gaiter split (2.5.C.1a)

Offside rear brake binding (3.7.B.1)

Offside rear brake recording little or no effort (3.7.B.5a)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear Trailing arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Trailing arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Stop lamp not working (1.2.1b)

ADVISE: O/S/F SHOCK ABSORBER LEAKING SLIGHTLY

ADVISE: O/S/R BRAKE BINDING SLIGHTLY