1990 Austin Mini Mayfair

Nearside Front Inner Corrosion to wheel arch tub, hole present

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Front Upper Driver's door hinge deteriorated but the door can still be readily opened and closed Play/loose (6.2.3 (c) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Headlamp aim unable to be tested (4.1.2 (b))

Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))

Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii))

Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Front Headlamp not working on main beam (4.1.1 (a) (ii))

Position lamp not working All (4.2.1 (a) (ii))

Rear fog lamp not working (4.5.1 (a) (ii))

Nearside Front Inner Corrosion to wheel arch tub, hole present

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Front Upper Driver's door hinge deteriorated but the door can still be readily opened and closed Play/loose (6.2.3 (c) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b))

Nearside Rear Position lamp not working (4.2.1 (a) (ii))

Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Position lamp not working (4.2.1 (a) (ii))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Brake pipe corroded, covered in grease or other material covered in underseal (1.1.11 (c))

Hazard warning switch faulty (4.4.2 (a) (i))

Lower Integral body structure is repaired but structural rigidity is not significantly reduced sill and floor panels repaired and covered in underseal (6.1.1 (d) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement inner wishbone bush perished (5.3.4 (a) (i))

Nearside Front Outer Drive shaft joint constant velocity boot severely deteriorated gaiter loose (6.1.7 (g) (i))

Nearside Rear Lower Integral body structure is corroded but structural rigidity is not significantly reduced inner wheel arch panel corroded (6.1.1 (c) (i))

Offside Front Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (1.1.21 (e) (i))

Offside Front Outer Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Rear Service brake fluctuating, but not excessively (1.2.1 (e))

Rear Service brake requirements only just met. It would appear that the braking system requires adjustment or repair (1.2.1 (c))

Fuel cap seal cracking.

Nearside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Play in both rear radius arm bearings.

Play in o/s/f wheel bearing.

Front Steering rack gaiter damaged or deteriorated, but preventing the ingress of dirt both (2.1.3 (g) (i))

Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arms (5.3.4 (a) (i))

Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (1.1.21 (e) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b))

Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Offside Front Brake hose excessively deteriorated (1.1.12 (b) (ii))

Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Offside Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt insecure (6.1.7 (g) (ii))

Steering column top bearing excessively worn (2.2.2 (b))

All direction indicators flashing more than 120 times a minute (4.4.4 (a))

Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (1.1.21 (e) (i))

Fuel pipe chafing rubbing on nearside driveshaft (6.1.3 (c) (i))

Nearside Front Upper Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Front Upper Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Side repeater insecure (4.4.1 (c) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Side repeater incorrect colour (4.4.3 (a))

Offside Side repeater incorrect colour (4.4.3 (a))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Service brake efficiency below requirements (1.2.2 (a) (i))

Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) DANGEROUS

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Front suspension has slight play in a lower suspension ball joint Nearside and offside (2.5.B.1a)

Front suspension has slight play in a upper suspension ball joint Nearside and offside (2.5.B.1a)

Nearside Front wheel bearing has slight play (2.5.A.3c)

Nearside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

Offside Front wheel bearing has slight play (2.5.A.3c)

Side repeater slightly discoloured Faded in colour nearside and offside (1.4.A.2f)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Front wheel bearing has slight play (2.5.A.3c)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Oil leak

Side repeater slightly discoloured Nearside and offside faded in colour (1.4.A.2f)

Nearside front seat missing at time of test

Side repeater slightly discoloured both (1.4.A.2f)

Steering rack causing movement between sub-frame and body - further investigation strongly advised

Direction indicators flashing more than 120 times a minute hazzards (1.4.A.2g)

Exhaust emissions carbon monoxide content excessive (7.3.B.1a)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

brake drum locking device insecure Both rear hand brake clevis pins (3.5.1l)

Nearside Front Upper Suspension arm has slight play in a ball joint (2.4.G.2)

Nearside front seat missing at time of test

Offside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Side repeater slightly discoloured both (1.4.A.2f)

Steering rack causing movement between sub-frame and body - further investigation strongly advised

Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Fuel pipe/s corroded

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Side repeater slightly discoloured (1.4.A.2f)

Nearside front tyre perishing

Offside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Side repeater slightly discoloured (1.4.A.2f)

Offside sill panel corroding

Oil leak

Brakes imbalanced across an axle (3.7.B.5b)

Nearside Front Lower Suspension arm has excessive play in a ball joint (2.4.G.2)

Nearside Headlamp aim too high (1.8)

Nearside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid (3.6.A.1)

Nearside rear brake recording little or no effort (3.7.B.5a)

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Offside Front wheel bearing has excessive play (2.5.A.3c)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Rear Brakes imbalanced across an axle (3.7.B.5b)

Windscreen washer provides insufficient washer liquid (8.2.3)

Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Fuel pipe/s corroded

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Side repeater slightly discoloured (1.4.A.2f)

Nearside front tyre perishing

Offside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Side repeater slightly discoloured (1.4.A.2f)

Offside sill panel corroding

Oil leak

Centre Front registration plate deteriorated but not likely to be misread (6.3.1d)

Outer Front Exhaust has a minor leak of exhaust gases (7.1.2)

Exhaust has a minor leak of exhaust gases (7.1.2)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)

Offside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Exhaust has a minor leak of exhaust gases (7.1.2)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)

Nearside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

Offside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)

Offside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

front brake juddering slightly (3.7.A.2b)

offside rear tyre perishing

Nearside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)

Offside Rear fog lamp not working (1.3.2b)

Rear fog lamp tell tale not working (1.3.1b)

Nearside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

front brake juddering slightly (3.7.A.2b)

offside rear tyre perishing

Nearside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Headlamp aim too low (1.8)

Offside Front Body has a sharp edge caused by corrosion (6.1.C.1)

Offside Front Body has a sharp edge caused by corrosion (6.1.C.1)

Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Tyre has a bulge, caused by separation or partial failure of its structure (4.1.D.1b)

Offside Rear fog lamp not working (1.3.2b)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Rear fog lamp tell tale not working (1.3.1b)

Fuel pipe/s corroded

Nearside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

Offside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Oil leak

corrosion to both front inner wings

corrosion to offside front bulk head around brake servo mount

corrosion to rear floors

rear brakes slightly imballanced

slight corrosion to both outer sills

advisorys as issued with vt30 on 28/09/2010

Bonnet cannot be secured in the closed position (8.4.1)

Exhaust emissions carbon monoxide content excessive (7.3.B.1a)

Horn not working (1.6.2a)

Sub-frame rubber bush deteriorated resulting in excessive movement (2.4.G.2)

both front floors corroding

front brake juddering slightly (3.7.A.2b)

front bulkhead corroding by subframe upper mounts

nearside a panel corroding

nearside front inner wheel arch corroding

offside inner a post corroding by door hinge2

offside of boot floor corroding

offside panel below windscreen corroded

slight play in front subframe upper rear mounts (on bulkhead)

Exhaust system not adequately supported (7.1.1)

Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Oil leak

corrosion along both inner sills

corrosion to rear floor on both side in front of valance

heavy corrosion to both front inner wings

heavy corrosion to front floor on both sides

heavy corrosion to offside front panel

heavy corrosion to offside rear valance

nearside front brake binding slightly