1989 Talbot Express 1000 P

Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b))

Nearside Front Direction indicator not working (4.4.1 (a) (ii))

Nearside Front Headlamp lens missing (4.1.1 (b) (ii))

Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Nearside Front Windscreen wiper blade missing (3.4 (b) (ii))

Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Offside Front Headlamp not working on main beam (4.1.1 (a) (ii))

Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Offside Front Driver's seat insecure (6.2.5 (a) (ii)) DANGEROUS

Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) DANGEROUS

Front Brake disc worn, pitted or scored, but not seriously weakened both sides (1.1.14 (a) (ii))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Lower Gearbox mounting defective ()

Offside Front Exhaust mounting defective (6.1.2 (a))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Leaf spring has slight wear in an anchor pin and/or bush both sides (5.3.4 (a) (i))

Rear Shock absorbers has a slightly worn bush both sides (5.3.2 (c))

Front Brake disc worn, pitted or scored, but not seriously weakened both (1.1.14 (a) (ii))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Nearside Outer Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Inner Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Outer Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Leaf spring has slight wear in an anchor pin and/or bush both (5.3.4 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened both (1.1.14 (a) (ii))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Headlamp aim too high both (4.1.2 (a))

Horn not working (7.7 (a))

Nearside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Nearside Outer Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Inner Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Outer Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Leaf spring has slight wear in an anchor pin and/or bush both (5.3.4 (a) (i))

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Horn not working (7.7 (a))

Nearside Front Suspension arm ball joint excessively worn Lower (5.3.4 (a) (i))

Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i))

Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Under body sill (6.1.1 (c) (i))

Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wheel arch (6.1.1 (c) (i))

Offside Headlamp light intensity severely reduced (4.1.4 (a))

Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i))

Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Under body sill (6.1.1 (c) (i))

Position lamp switch does not operate in accordance with the requirements (4.2.2 (a))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Windscreen wiper does not clear the windscreen effectively Both (3.4 (b) (ii))

Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i))

Nearside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i))

Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i))

Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i))

Nearside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Wheel bearing has slight play both (5.1.3 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Wheel bearing has slight play both (5.1.3 (a) (i))

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Headlamp insecure both (4.1.1 (c))

Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a))

Driver's seat insecure (6.2.5 (a) (ii)) DANGEROUS

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Wheel bearing has slight play both (5.1.3 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Wheel bearing has slight play both (5.1.3 (a) (i))

Emissions not tested (8.2.1.2 (d))

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Headlamp insecure (4.1.1 (c))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Headlamp insecure (4.1.1 (c))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Exhaust fumes causing a danger to health of persons on board (6.1.2 (b) (ii)) DANGEROUS

exhaust rubbers missing

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Nearside Headlamp insecure (1.7.3)

Offside Front Suspension component mounting prescribed area is excessively corroded chassis (2.4.A.3)

Offside Front Suspension component mounting prescribed area is excessively corroded chassis /wheel arch (2.4.A.3)

Offside Front Suspension component mounting prescribed area is excessively corroded jacking point (2.4.A.3)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside Headlamp insecure (1.7.3)

Nearside Front Lower Front suspension ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)

Offside Front Brake hose has slight corrosion to ferrules x2 (3.6.B.4e)

Offside Front Front constant velocity joint gaiter damaged, but preventing the ingress of dirt (2.5.C.1a)

both outter sills corroded

Nearside Front Front wheel bearing has slight play (2.5.A.3c)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement front (2.4.G.2)

Nearside Front Vehicle structure has slight corrosion (6.1.B.2)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement front (2.4.G.2)

underbody/components covered in underseal like substance

Nearside Front Inner Suspension arm rubber bush deteriorated but not resulting in excessive movement front (2.4.G.2)

Nearside Front chassis slightly corroded

Nearside inner and outer sill slightly corroded

Offside Front Inner Suspension arm rubber bush deteriorated but not resulting in excessive movement front (2.4.G.2)

Offside Front chassis slightly corroded

brake pipes and ferrules covered in grease like substance, unable to fully inspect

underbody and components covered in underseal, unable to fully inspect

underbody/components dirty/muddy

converters fitted to headlamps

corrosion to offside front chassis leg - suggest attension but no hole

hydrocarbons high - ok when vehicle idle speed raised

slight play in nearside and offside front wheel bearings

Exhaust emissions hydrocarbon content excessive (7.3.B.1b)

Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement (7.2.4b)

Nearside Headlamp aim too high (1.8)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Registration plate lamp not working (1.1.C.1d)

corrosion to offside front chassis leg - suggest attension but no hole

exhaust tail pipe corroded - suggest replace

front brake discs corroded

nearside and offside headlamp reflectors deteriated

slight play in nearside and offside front wheel bearings

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Centre Rear Registration plate lamp not working (1.1.C.1d)

Emissions not tested (7.0)

Front Exhaust has a major leak of exhaust gases (7.1.2)

Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement (7.2.4b)

Nearside Front position lamp(s) has less than 50% of the light sources illuminating (1.1.A.3b)

Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Nearside Inner Front constant velocity joint is insecure (2.5.C.1b)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside Inner Front constant velocity joint is insecure (2.5.C.1b)

Parking brake lever, pawl mechanism pivots or their associated mountings are insecure (3.1.4b)

Rear fog lamp tell tale not working (1.3.1b)

Offside Front Driver's seat insecure (6.2.A.1) DANGEROUS

Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)

Offside Front wheel bearing has slight play (2.5.A.3c)

Offside Rear wheel bearing has slight play (2.6.2)

Nearside Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Nearside Inner Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear wheel bearing has slight play (2.6.2)

Offside Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Offside Rear wheel bearing has slight play (2.6.2)

n/s/f inner lower arch corroded but out side prescribed area

o/s ands n/s headlight aim weak

underside heavely waxoiled

Horn not working (1.6.2a)

Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Rear fog lamp tell tale not working (1.3.1b)

Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Nearside Inner Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear wheel bearing has slight play (2.6.2)

Offside Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Offside Rear wheel bearing has slight play (2.6.2)

n/s/f inner lower arch corroded but out side prescribed area

o/s ands n/s headlight aim weak

underside heavely waxoiled

underside heavely bwaxoiled

Hazard warning switch faulty (1.4.B.1d)

Inner Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Direction indicator adversely affected by the operation of another lamp (1.4.A.2h)

Nearside Rear Leaf spring anchor bracket bolt missing (2.4.B.6c)

Offside Front constant velocity joint gaiter split (2.5.C.1a)

Offside Inner Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Outer Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Registration plate lamp not working (1.1.C.1d)

exhaust rubbers perished

os outer sill holed outside prescribed aresa

Rear Brake pipe slightly corroded (3.6.B.2c)

Exhaust has part of the system slightly deteriorated (7.1.1a)

Front Vehicle structure has slight corrosion (6.1.B.2)

Nearside Front Brake hose slightly deteriorated (3.6.B.4d)

Nearside Front Brake pipe slightly corroded (3.6.B.2c)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Front Vehicle structure has slight corrosion (6.1.B.2)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Brake hose slightly deteriorated (3.6.B.4d)

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Vehicle structure has slight corrosion (6.1.B.2)

Offside Headlamp not in good working order but not adversely affecting beam image (1.2.4a)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Oil leak

Rear Brake hose slightly deteriorated (3.6.B.4d)

Vehicle structure has slight corrosion (6.1.B.2)

n/s and o/s sills inner and outter corroded

Exhaust has part of the system slightly deteriorated (7.1.1a)

Front Vehicle structure has slight corrosion (6.1.B.2)

Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement (7.2.4b)

Nearside Front Brake hose slightly deteriorated (3.6.B.4d)

Nearside Front Brake pipe slightly corroded (3.6.B.2c)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Front Vehicle structure has slight corrosion (6.1.B.2)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Brake hose slightly deteriorated (3.6.B.4d)

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Vehicle structure has slight corrosion (6.1.B.2)

Offside Headlamp not in good working order but not adversely affecting beam image (1.2.4a)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Oil leak

Rear Brake hose slightly deteriorated (3.6.B.4d)

Rear Brake pipe slightly corroded (3.6.B.2c)

Vehicle structure has slight corrosion (6.1.B.2)

n/s and o/s sills inner and outter corroded

Nearside Front Direction indicator adversely affected by the operation of another lamp (1.4.A.2h)

Nearside Front Side repeater not working (1.4.A.2c)

Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear rear brake recording little or no effort (3.7.B.5a)

Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Headlamp not in good working order (not working) (1.2.4a)

Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Registration plate lamp not working (1.1.5c)

Windscreen washer provides insufficient washer liquid (8.2.3)

Front Vehicle structure has slight corrosion (6.1.B.2)

Nearside Front Vehicle structure has slight corrosion (6.1.B.2)

Offside Front Vehicle structure has slight corrosion (6.1.B.2)

Vehicle structure has slight corrosion (6.1.B.2)

exhaust manifold has a slight blow

front and rear number plates starting to discolour

front brake discs slight corroded

front tyres on the outter walls starting to perrish

Nearside Front constant velocity joint gaiter split (2.5.C.1a)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Rear Registration plate lamp not working (1.1.5c)

exhaust manifold has a slight blow

front and rear number plates starting to discolour

front brake discs slight corroded

front tyres on the outter walls starting to perrish