1989 Rover Mini

cannot fully inspect underside of vehicle due to underseal

surface corrotion under vehicle

All direction indicators not working (4.4.1 (a) (ii))

All position lamps not working (4.2.1 (a))

Emissions not tested (8.2.1.2 (d))

Hazard warning switch inoperative (4.4.2 (a) (ii))

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords 145/70/12 (5.2.3 (d) (i))

Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Windscreen wiper not working (3.4 (a))

Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering arch (6.1.1 (c) (ii)) DANGEROUS

Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering FLOOR (6.1.1 (c) (ii)) DANGEROUS

Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering arch (6.1.1 (c) (ii)) DANGEROUS

Offside Vehicle structure has excessive corrosion which adversely affects braking or steering FLOOR (6.1.1 (c) (ii)) DANGEROUS

cannot fully inspect underside of vehicle due to underseal

surface corrotion under vehicle inc suspention componants

Nearside Front Suspension arm has slight play in a ball joint (2.4.G.2)

Nearside Rear Radius arm has slight play in a pin/bush (2.4.G.2)

corrotion under vehicle

hevely underseald under vehicle

Front Front position lamp(s) not working both side lights (1.1.A.3b)

Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor x 3 (6.1.B.2)

Offside Front Front wheel bearing rough when rotated (2.5.A.2)

Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor (6.1.B.2)

Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch (6.1.B.2)

Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor (6.1.B.2)

Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch (6.1.B.2)

Rear Front position lamp(s) not working both (1.1.A.3b)

Rear fog lamp not working (1.3.2b)

corrotion under vehicle

oil leak

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Various welding repairs carried out on vehicle body.

Hazard warning lamps inoperative (1.4.B.1b)

Nearside Front Sub-frame attachment rubber mounting bonding deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Headlamp aim too high (1.8)

Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Rear position lamp(s) not working (1.1.A.3b)

Offside Rear Stop lamp not working (1.2.1b)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Rear Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Various welding repairs carried out on vehicle body.

Parking brake: efficiency below requirements (3.7.B.7)

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Nearside Rear Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Offside Rear Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

n/s/r wheel towing in

All position lamps not working (1.1.A.3b)

Headlamp not working on dipped beam (1.7.5a)

Headlamp not working on main beam (1.7.5a)

Nearside Front Tie bar/rod which is adjustable, locking device insecure (2.4.G.1)

Nearside Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Nearside Steering rack gaiter split (2.2.D.2d)

Offside Front Brake hose has insufficient room to move, resulting in fouling on any part (3.6.B.4a)

Offside Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Offside Rear fog lamp not working (1.3.2b)

Offside Side repeater not working (1.4.A.2c)

Registration plate lamp not working (1.1.C.1d)

Front Bumper Loose

Fuel pipe/s corroded

Nail in offside front tyre

Offside Front Front suspension has slight play in a upper suspension ball joint (2.5.B.1a)

Centre Exhaust mounting missing (7.1.1b)

Front Exhaust system not adequately supported (7.1.1)

Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f)

Nearside Front Front wheel bearing rough when rotated (2.5.A.2)

Nearside Front Headlamp aim too far to the right (1.8)

Nearside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Tie bar/rod insecure (2.4.G.1)

Nearside Rear Rear wheel bearing has excessive play (2.6.2)

Offside Front Headlamp aim too low (1.8)

Offside Front Tie bar/rod insecure (2.4.G.1)

Offside Rear Sub-frame attachment bracket/mounting modified and seriously weakened (2.4.A.2)

Rear Exhaust system not adequately supported (7.1.1)

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Front Bumper Loose

Fuel pipe/s corroded

Nail in offside front tyre

Nearside and Offside lower ball joint dust covers perished.

Offside Front Front suspension has slight play in a upper suspension ball joint (2.5.B.1a)

Bonnet cannot be secured in the closed position (8.4.1)

Nearside Front Brake hose twisted (3.6.B.4c)

Nearside Front Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a)

Nearside Front Front suspension has excessive play in a upper suspension ball joint (2.5.B.1a)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Headlamp aim too high (1.8)

Offside Front Brake hose has insufficient room to move, resulting in fouling on any part (3.6.B.4a)

Offside Front Brake pipe inadequately clipped (3.6.B.1)

Offside Front Sub-frame rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Offside Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Headlamp aim too high (1.8)

Offside Steering rack gaiter split (2.2.D.2d)

Vehicle Identification Number not permanently displayed (6.3.5.a)

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Front passenger door cannot be opened from inside the vehicle (6.2.B.1b)

Front passenger door cannot be opened from outside the vehicle (6.2.B.1b)

Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f)

Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Front Direction indicator incorrect colour (1.4.A.2f)

Nearside Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Upper Suspension arm has excessive play in a ball joint (2.4.G.2)

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Rear Brake cable has a seized clevis joint pivot (3.5.1c)

Nearside Rear Radius arm has excessive play in a pin/bush (2.4.G.2)

Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Direction indicator incorrect colour (1.4.A.2f)

Offside Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Tie bar/rod severely distorted (2.4.G.1)

Offside Front brake disc excessively pitted (3.5.1h)

Offside Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Offside Rear Brake cable has wires broken and is significantly weakened (3.5.1b)

Offside Rear Rear fog lamp missing (1.3.2a)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Parking brake lever has no reserve travel (3.1.6b)

Parking brake: efficiency below requirements (3.7.B.7)

Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Service brake: efficiency below requirements (3.7.B.7)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1) DANGEROUS

Bonnet cannot be secured in the closed position (8.4.1)

Front Exhaust mounting missing (7.1.1b)

Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Front registration plate missing (6.3.1a)

Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f)

Nearside Brake cable has restricted free movement (3.5.1k)

Nearside Front Lower Suspension arm has excessive play in a ball joint (2.4.G.2)

Nearside Front Sub-frame rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Upper Suspension arm has excessive play in a ball joint (2.4.G.2)

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Headlamp not working on main beam (1.7.5a)

Nearside Inner Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Parking brake: efficiency below requirements (3.7.B.7)

Nearside Rear Service brake: efficiency below requirements (3.7.B.7)

Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Brake cable has wires broken and is significantly weakened (3.5.1b)

Offside Front Direction indicator incorrect colour (1.4.A.2f)

Offside Front Sub-frame rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Parking brake: efficiency below requirements (3.7.B.7)

Rear Exhaust system not adequately supported (7.1.1)

Rear Rear fog lamp not working (1.3.2b)

Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

no plate light dim

o/s/front inner wing corroded

o/s/rear inner wing corroded

Front Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Direction indicator slightly discoloured (1.4.A.2f)

Nearside Front Sub-frame has slight play in a pin/bush (2.4.G.2)

Offside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Sub-frame has slight play in a pin/bush (2.4.G.2)

Suspension joint offside lower dust cover split/missing