2016 Qingqi Qm

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Brake indicates slight fluctuation of brake effort (1.2.1 (e))

Front Headlamp light intensity reduced (4.1.4 (a))

Motorcycle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Brake indicates slight fluctuation of brake effort (1.2.1 (e))

Front Position lamp not working Side light (4.2.1 (a))

Handlebar excessively deformed (2.2.1 (c) (i))

Nearside Rear Footrest missing (6.2.12 (a))

Offside Rear Footrest missing (6.2.12 (a))

Rear Brake pedal has insufficient reserve travel (1.1.2 (a))

Roller brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Brake indicates slight fluctuation of brake effort (1.2.1 (e))

Front Headlamp light intensity reduced (4.1.4 (a))

Motorcycle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Brake indicates slight fluctuation of brake effort (1.2.1 (e))

Lights masked atmtime of test. Rear suspension has solid strut installed

Headlamp aim projected beam image obviously incorrect No discernable beam patern (4.1.2 (c))

Suspension arm pin or bush excessively worn Swing arm bushes (5.3.4 (a) (i))

Headlamp aim projected beam image obviously incorrect No discernable beam patern (4.1.2 (c))

Headlamp insecure (4.1.1 (c))

Rear Shock absorber has a serious fluid leak (5.3.2 (b))

Rear Shock absorber has an excessively worn bush Top and bottom (5.3.2 (c))

Drive chain so worn it is likely to fail (6.1.7 (c) (ii)) DANGEROUS

Front Headlamp aim too low (4.1.2 (a))

Front Stop lamp switch with a delay in operation (4.3.2 (a) (ii))

Rear Shock absorber has negligible damping effect (5.3.2 (b))

Roller brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i))

Rear Shock absorber has negligible damping effect (5.3.2 (b))

Front Stop lamp switch does not operate in accordance with the requirements (4.3.2 (a) (i))

Rear Brake pedal is bent but brake can still be readily applied (1.1.2 (d))

Horn not working (7.7 (a) (ii))

Rear Rear reflector missing (4.8.2 (a) (ii))

Rear Wheel bearing has excessive play (5.1.3 (a) (i))

Roller brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i))

Rear Brake has no recorded effort at a wheel (1.2.1 (a) (ii)) DANGEROUS

Rear Brake pad(s) less than 1.0 mm thick (1.1.13 (a)) DANGEROUS

Rear Tyre tread depth is below minimum requirements of 1.0mm (5.2.3 (e)) DANGEROUS

Drive chain sprocket worn, but not excessively (6.1.7 (c) (i))

Drive chain worn but not considered excessive (6.1.7 (c) (i))

Exhaust noisy (8.1.1 (a))

Front Tyre worn close to the legal limit (5.2.3 (e))

Handlebar deformed but serviceable (2.2.1 (c) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))